Номер модели: 7075 Применение: украшения, теплоотвод, транспортные средства, двери и окна, стеклянная стена, резервуар Класс: серия 7000 Техника: Горячекатаный Прокат: T3 - T8 Поверхность: мельница Спецификация: Китайский стандартный код HS: 7606129000 Тип: Форма алюминиевых листов: Плоская Обработка поверхности: Обработка поверхности Сплав: Сплав Сертификация: ASTM, JIS, GB / T, EN, ASTMB Торговая марка: HM Происхождение: Китай 7075 T6 Лист из алюминиевого сплава с гладкой отделкой \ n \ nСплав: 1050, 1060, 1100 , 3003, 5052 5083 6061 5005 6063 6082 7075 и т. Д. \ NТемпература: H12. H14. H16. H18. H112. H22. H24. H26. H32. H34. H36. H38. O и т. Д. \ NТолщина: 0,2 мм - 400 мм \ nШирина: менее 2800 мм \ nДлина: менее 10000 мм \ nУпаковка: стандартная упаковка, покрытие оберточной бумагой и полиэтиленовой пленкой, затем упаковка стальной лентой и деревянным ящиком / поддоном \ nПроисхождение: Китай \ nЛидер Время: В течение 25 дней \ nПроизводительность: 4000MT / Месяц \ nОплата: T / T, безотзывный аккредитив по предъявлении \ nПримечания: Конкретные требования к сплаву, состоянию или спецификации могут быть обсуждены по вашему запросу.
Aluminium Plate / Slab 5052 |
Typical Chemistry (% Maximum unless shown as a range) |
\ п \ п \ п
Cu | Si + Fe | Mn | Mg | Zn | Cr | Al |
0.10 | 0.45 | 0.10 | 2.2 / 2.8 | 0.10 | 0.15 / 0.35 | Balance |
\ п \ п \ п
Characteristics |
5052 is one of the higher strength non-heat-treatable alloys. It has a high fatigue strength and is a good choice for structures subjected to excessive vibration. The alloy has excellent corrosion resistance, particularly in marine atmospheres. The formability of the grade is excellent and in the annealed condition it offers higher strengths than 1100 or 3003 grades. |
Typical Applications |
5052 is often used in high strength sheet metal work, marine components, appliances, fuel and oil tubing. |
Mechanical Properties |
\ п \ п \ п
| Tensile Strength | Yield Strength | Elongation | Brinell Hardness |
| ksi | MPa | ksi | MPa | % in 2" (50mm) |
|
5052-0 | 28.0 | 196 | 13.0 | 91 | 25 | 47 |
5052-H32 | 33.0 | 231 | 28.0 | 196 | 12 | 60 |
5052-H34 | 38.0 | 266 | 31.0 | 217 | 10 | 68 |
\ п \ п \ п \ п
Aluminium Plate / Slab 5083 |
Typical Chemistry (% Maximum unless shown as a range) |
\ п \ п \ п
Cu | Si | Fe | Mn | Mg | Zn | Cr | Ti | Al |
0.10 | 0.40 | 0.40 | 0.3 / 1.0 | 4.0 / 4.9 | 0.25 | 0.05 / 0.25 | 0.15 | Balance |
\ п \ п \ п
Characteristics |
5083 is the highest strength non-heat-treatable alloy in commercial use. It has good formability and weldability and retains excellent tensile strength in the weld zone by virtue of its as-rolled properties. It is used most often in structures requiring high weld efficiency and maximum weld strength. 5083 also has excellent resistance to corrosion. |
Typical Applications |
5083 is commonly used in highly stressed welded assemblies, dump truck boxes, storage tanks, and cryogenic vessels. |
Mechanical Properties |
\ п \ п \ п
| Tensile Strength | Yield Strength | Elongation | Brinell Hardness |
| ksi | MPa | ksi | MPa | % in 2" (50mm) |
|
5083-0 | 42 | 294 | 21 | 147 | 22 | - |
5083-H321 | 46 | 322 | 33 | 231 | 16 | - |
\ п \ п \ п \ п
Aluminium Plate / Slab 6061 |
Typical Chemistry (% Maximum unless shown as a range) |
\ п \ п \ п
Cu | Si | Fe | Mn | Mg | Zn | Cr | Ti | Al |
0.15 / 0.40 | 0.4 / 0.8 | 0.70 | 0.15 | 0.80 / 1.2 | 0.25 | 0.04 / 0.35 | 0.15 | Balance |
\ п \ п \ п
Characteristics |
6061 is a heat-treatable grade widely used in light to medium strength structural applications. The alloy has good corrosion resistance and weldability and possesses good formability in the 0 to T4 tempers. 6061 does lose appreciable strength when welded and it is replaced by the 5000 series alloys where afterweld strength is a prime consideration. |
Typical Applications |
6061 is used in structural areas where both strength and corrosion resistance is required, truck bodies and frames, and towers. |
Mechanical Properties |
\ п \ п \ п
| Tensile Strength | Yield Strength | Elongation | Brinell Hardness |
| ksi | MPa | ksi | MPa | % in 2" (50mm) |
|
6061-0 | 18.0 | 126 | 8.0 | 56 | 25 | 30 |
6061-T4 | 34.0 | 238 | 22.0 | 154 | 21 | 65 |
6061-T6 (T651) | 44.0 | 308 | 41.0 | 287 | 17 | 95 |
\ nМы также можем изготовить меньшие размеры резки в соответствии с требованиями клиентов. \ n \ n
Группа Продуктов : Алюминиевый лист и плита